RX packets experienced errors-checkpoint-gaia

RX packets experienced errors-checkpoint-gaia

Vendor: checkpoint

OS: gaia

Description:
Indeni tracks the number of packets that had issues and alerts if the ratio is too high.

Remediation Steps:
Packet errors usually occur when there is a mismatch in the speed and duplex settings on two sides of a cable, or a damaged cable.

chkp-gaia-clish_show_interfaces_all-vsx

name: chkp-gaia-clish_show_interfaces_all-vsx
description: Run "show interfaces all" over clish in VSX
type: monitoring
monitoring_interval: 5 minute
requires:
    vendor: checkpoint
    os.name: gaia
    vsx: 'true'
    role-firewall: 'true'
comments:
    network-interface-state:
        why: |
            To check the network interface  state for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-admin-state:
        why: |
           To check the interface admin state for all the interfaces on the system
        how: |
           By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-speed:
        why: |
            To check the  network interface  speed for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-duplex:
        why: |
            To check the network interface duplex state for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-ipv4-address:
        why: |
            To check the network interface ipv4 address for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-ipv4-subnet:
        why: |
            To check the network interface ipv4 subnet for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false
    network-interface-type:
        why: |
            To check the network interface state for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-mtu:
        why: |
            To check the network interface MTU for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-mac:
        why: |
            To check the network interface mac for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-description:
        why: |
            To check the network interface description for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-tx-bits:
        why: |
            To check the network interface transmitted bits for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-rx-bits:
        why: |
            To check the network interface recieved bits for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-tx-packets:
        why: |
             To check the network interface transmitted packets for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-rx-packets:
        why: |
            To check the network interface recieved packets for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-tx-errors:
        why: |
            To check the network interface "tx-errors" for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-rx-dropped:
        why: |
            To check the network interface "rx-dropped" packets for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-tx-overruns:
        why: |
            To check the network interface "tx-overruns" for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-rx-overruns:
        why: |
            To check the network interface "rx-overrruns" for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-tx-carrier:

        why: |
            To check the network interface "tx-carrier" for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-rx-frame:
        why: |
            To check the network interface "rx-frame"  for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interfaces:
        why: |
            To list all the network interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-admin-state-logical:
        why: |
            To check the interface network state for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-state-logical:
        why: |
            To check the network interface logical state for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false

    network-interface-:
        why: |
            To check the network interface names for all the interfaces on the system
        how: |
            By parsing the information recived from commands "ifconfig -a", "ethtool" as well as Check point clish
            command "show interfaces all"
        can-with-snmp: false
        can-with-syslog: false
steps:
   -  run:
          type: SSH
          file: show-interfaces-all-vsx.remote.1.bash
      parse:
          type: AWK
          file: show-interfaces-all-vsx.parser.1.awk

cross_vendor_rx_error

Failed to fetch the data: https://bitbucket.org/indeni/indeni-knowledge/src/master/rules/templatebased/crossvendor/cross_vendor_rx_error.scala